Properties

With excellent   temperature resistance;

It can be used in high   temperature between 150℃~300℃;

The paint film with anti-acid,   anti-alkali performance in the high temperature.

Designed Applications

Used for Petroleum, chemical industry, mining ,electric power,   building materials, etc.

Used for high-temperature and anticorrosive equipment boiler,   vent-pipe, chimney, heat conduit , dust-cleaning apparatus of cement plantunder 300℃(572℉)

Color

Iron red

Working Parameters

Lustre

Solid volume

Flash point

Drying time 25℃(77℉)

Semi-lustrous

66±2%

31℃(87.8℉)

Surface drying time: 4   hrs

Hard drying time: 20hrs

Coating thickness and   theoretical coating ratio

Actual coating ratio          Loss coefficient properly   considered

Intervals of recoating

Surface Treatment

Ø     Use sand blasting till the   level of Sa 2.5 to remove oxide skin and iron rust, roughness: 40~75 microns;

Ø     Be sure to get rid of the oil   stain and weld spatters on the steel plate before rust removal, and burnish   welding seams and closed angles;

Ø     For the partially rusty part,   adopt local sand blasting till Sa2.5 Level for rust removal.

Temperature of

base material

The temperature of base   material must be over 3℃(37.4℉) above the dew point.

When the temperature of   base material is below 5℃(41℉), the reaction of epoxy and solidifying agent becomes slow, which   is not suitable for using.

Usage

Mixing

The product is packed in   two containers separately that form a unit. For use every time, completely   and uniformly mix it according to the specified compounding ratio, and then   leave it stationary for slaking for 30 minutes. The product must be used up   within the specified mixture pot life.

Mixing ratio

A: B=13.4: 1 (volume   ratio)

A: B=20: 1 (weight ratio)

Time of cure 25℃(77℉)  30 mins

Pot life: (after mixture)

Ways of

Coating

Airless spraying, aerial   spraying, brush painting or roller painting

Airless spraying

Diluting agent

GLX-7 Thinner

Dosage

5% (Weight of paint)

Spray nozzle

calibre

about 0.4~0.5mm(0.016~0.020″)

Spraying pressure

15~17MPa

(about 150~170Kg/cm² ,2100~2200psi)

Aerial spraying

Diluting agent

GLX-7 Thinner

Dosage

5-10%（Weight of paint）

Spray nozzle

calibre

2.0~2.5mm(0.079~0.098″)

Air pressure

0.3~0.6MPa

(3~6Kg/cm² ,42~85psi)

Brushing paint;

Roller

paint

Only suitable for repair   and small-area coating.

Cleaning agent

GLX-7 Thinner

Safety protection

There should be good   ventilating devices provided at the work site. During working, wear the   appliances for labor protection such as gauze mask, spectacles, gloves, etc.   to avoid skin contact with and suction of solvent or paint fog. Smoking is   forbidden at the work site, and all fire sources shall be isolated.

Storage and

Packing

Packing

20 kl Group

Ingredient A

20L Pail Pack

18.6 kl

27kg

Ingredient B

5L Pail Pack

1.4 kl

1.35kg

Storage

25℃

(77℉)

12 months (Exceeding the   storage life, the product must be retested, and can be used only if passing   the test.)

The product should be   kept at cool and dry place, away from heat sources and fire sources.

Precautions

l           Long-time exposure of the   product to the atmospheric environment will cause atomizing and color fading,   though these phenomena will not influence the ability.

l           Before the equipment with   this paint is used firstly, it must be heated in 100℃   for 1 hour in order to it`s paint film cured completely. Otherwise the anti-acid,   anti-alkali performance will be weaken.

1. The data   in the Description of Product are merely the instruction for use. This   company will provide technical support and on-site service at the user’s   request so as to ensure the normal proceeding of the working. For non-normal   coating and its application, this Company only guarantees the technical   indicators of the products.    

2. On the   basis of the development of technology, the application of high and new-tech   materials and the user’s requirements, we will improve the compounding   formula and the product quality, and make further amendments in the   Description of Product.