Properties

The adoption of nuisance   free antirust pigment is good for environmental protection;

Provided with good oil   resistant and solvent resistant ability;

With excellent saltfog   resistant, water resistant and antirust property;

The paint film is   tenacious and abrasion resistant, of excellent adhesive and impact resistant   ability;

The content of lead and heavy   metal all are in accordance   with the requirement of environmental standards in theUnited Statesand Europe.

Designed Applications

Applicable to ships, offshore installations, bridges, papermaking,   chemical industry, petrochemical plant, power plant, etc.

Color

Iron red/grey

Working Parameters

Lustre

Solid volume

Flash point

Drying time 25℃(77℉)

Semi-lustrous

65±2%

29℃(84.2℉)

Surface drying time: 2   hrs

Hard drying time: 24 hrs

Coating thickness and   theoretical coating ratio

Actual coating ratio          Loss coefficient properly   considered

Intervals of recoating

Suggested times of   coating

Airless spraying once,   dry coating thickness as 60~80 microns, brush painting or roller painting for   2~3 times.

Surface Treatment

Ø     Use sand blasting till the   level of Sa 2.5 to remove oxide skin and iron rust, roughness: 40~75 microns;

Ø     Be sure to get rid of the oil   stain and weld spatters on the steel plate before rust removal, and burnish   welding seams and closed angles;

Ø     For the surface coated with   shop primer, oil stain, moisture, zinc salts and dust must be removed. For   the partially rusty part, adopt local sand blasting till Sa2.5 Level for rust   removal, or adopt elastic grinding wheel buffing till St.3 Level.

Temperature of

base material

The temperature of base   material must be over 3℃(37.4℉) above the dew point.

When the temperature of   base material is below 5℃(41℉), the reaction of epoxy and solidifying agent becomes slow, which   is not suitable for using.

Usage

Mixing

The product is packed in   two containers separately that form a unit. For use every time, completely   and uniformly mix it according to the specified compounding ratio, and then   leave it stationary for slaking for 30 minutes. The product must be used up   within the specified mixture pot life.

Mixing ratio

A: B=4: 1 (volume ratio)

A: B=7: 1 (weight ratio)

Time of cure 25℃(77℉)  30 mins

Pot life: (after mixture)

Ways of

Coating

Airless spraying, aerial   spraying, brush painting or roller painting

Airless spraying

Diluting agent

GLX-7 Thinner

Dosage

10% (Weight of paint)

Spray nozzle

calibre

about 0.4~0.5mm(0.016~0.020″)

Spraying pressure

15~17MPa

(about 150~170Kg/cm² ,2100~2200psi)

Aerial spraying

Diluting agent

GLX-7 Thinner

Dosage

10%（Weight of paint）

Spray nozzle

calibre

2.0~2.5mm(0.079~0.098″)

Air pressure

0.3~0.6MPa

(3~6Kg/cm² ,42~85psi)

Brushing paint;

Roller

paint

Only suitable for repair   and small-area coating.

Cleaning agent

GLX-7 Thinner

Safety protection

There should be good   ventilating devices provided at the work site. During working, wear the   appliances for labor protection such as gauze mask, spectacles, gloves, etc.   to avoid skin contact with and suction of solvent or paint fog. Smoking is   forbidden at the work site, and all fire sources shall be isolated.

Former compatible paint

We recommend that this   paint should be used in company with following  products:

If you want to know other   kinds of compatible coating, please consult the  technical services division in Wuhan Gelin Coating   Limited Company. 

Latter

compatible paint

We recommend that this   paint should be used in company with following  products:

If you want to know other   kinds of compatible coating, please consult the  technical services division in Wuhan Gelin Coating   Limited Company. 

Storage and

Packing

Packing

20 kl Group

Ingredient A

20L Pail Pack

15.8 kl

Ingredient B

5L Pail Pack

4.2 kl

Storage

25℃

(77℉)

12 months (Exceeding the   storage life, the product must be retested, and can be used only if passing   the test.)

The product should be   kept at cool and dry place, away from heat sources and fire sources.

Precautions

l           Overthickness of coating   should be avoided. Thick coating may result in the problem to the binding   power between the layers;

l           Overthick coating will   prolong the minimum interval of coating and handling time, and may have   adverse effect on the intervals of coating;

l           Long-time exposure of the   product to the atmospheric environment will cause atomizing and color fading,   though these phenomena will not influence the anticorrosive ability.

1. The data   in the Description of Product are merely the instruction for use. This   company will provide technical support and on-site service at the user’s   request so as to ensure the normal proceeding of the working. For non-normal   coating and its application, this Company only guarantees the technical   indicators of the products.    

2. On the   basis of the development of technology, the application of high and new-tech   materials and the user’s requirements, we will improve the compounding   formula and the product quality, and make further amendments in the   Description of Product.